BEHIND
THE SCREENS

Material recovery: define the application before choosing your MLT CUCCOLINI screen

09/11/2026 16:20

BEHIND
THE SCREENS

Material recovery: define the application before choosing your MLT CUCCOLINI screen

09/11/2026 16:20

How much usable material can you recover? The answer starts with your product, the required separation and the conditions in which the equipment will operate.

A material recovery project needs a clear basis for assessing what can realistically be achieved. Throughput alone does not provide that answer: you also need to establish how much material can be recovered in the required fraction and what separation result the process can deliver.

At MLT Cuccolini, we start with your application, not a machine specification. The information you share helps us assess the material, select the appropriate screening technology and develop a configuration suited to your process.

Where performance needs to be verified, laboratory trials or rental equipment provide a practical way to move from expectations to measured results.

Start with the material and the recovery objective

The first step is to define which fractions you need to separate, which material you want to recover and the mesh aperture you have selected.

The recoverable quantity must then be assessed against the behaviour of your specific product, using the most appropriate of the three screening technologies available in our range.

This means considering throughput and separation performance together. The relevant question is not simply how much material the screen can process, but how much of the required fraction it can deliver under the conditions assessed.

Share the available application information from the outset, including any uncertainties. Knowing what still needs to be established helps us identify the right assessment route.

Use trials to establish what is achievable

When the material’s screening behaviour needs to be verified, we offer two routes: trials at our laboratory in Reggio Emilia, Italy, or rental of a small- or medium-sized screen for testing at your site.

Both routes help establish the throughput and degree of separation achieved under the trial conditions. The results also provide a basis for discussing adjustments or changes where further improvement is needed.

Laboratory trials in Reggio Emilia

Laboratory trials allow us to assess your material using the selected mesh aperture and screening technology.

The purpose is to observe the product’s behaviour and measure the resulting throughput and separation. These findings help us determine the next steps, including whether further adjustments or testing are appropriate before proposing a solution.

Rental equipment for on-site assessment

Our rental service allows you to evaluate the application at your own site using a small- or medium-sized MLT Cuccolini screen.

Rental machines are equipped with the essential accessories required for the application. This provides a practical setup for assessing performance without necessarily reproducing the complete configuration of the final installation.

The results can then be reviewed with our technical team to determine whether adjustments or configuration changes could improve performance.

A rental trial is therefore part of the assessment process—not automatically a specification for the equipment ultimately supplied.

 

Build the proposal around the complete operating context

Application data and, where required, trial results allow us to identify the solution to propose.

That assessment goes beyond screening technology and machine size. It also includes the equipment and configuration needed to support correct feeding of the screen.

To develop the proposal, we need to understand how the material will reach the machine, how feeding will be managed and how the screen will fit into the wider installation.

A throughput figure considered in isolation cannot define these requirements. The proposal needs to reflect how the equipment will actually be used.

Established applications can allow a faster quotation

Not every project requires the same level of testing.

Where an application is well established within MLT Cuccolini’s experience, we may be able to shorten the quotation process by selecting an appropriately configured screen from our range.

Application information remains essential. It allows us to check that your material, recovery objective and operating conditions are consistent with the proposed configuration.

Experience can make the selection process faster, but it does not remove the need to understand your requirements.

 

Consider feeding and handling as part of the recovery process

The installation context helps us propose configurations suited to the plant or system into which the screen will be integrated.

Where manual feeding is required, we can also consider arrangements designed to minimise product waste and limit the consequences of potentially incorrect operator actions.

For a recovery project, this matters beyond the separation itself. The way material is introduced into the machine should also support the objective of retaining useful product.

Discussing the intended operating procedure early allows these requirements to be addressed in the configuration rather than left until installation.

What should a recovery proposal make clear?

Whether you are assessing the project from an engineering, production or purchasing perspective, clarify the following points:

  • Which product fraction is intended for recovery?
  • What mesh aperture has been selected?
  • What data or trials support the expected recoverable quantity?
  • What throughput and separation performance have been demonstrated, and under which conditions?
  • Are further checks or adjustments required?
  • How will the screen be fed?
  • Which configuration features address the installation and operating requirements?

These questions help distinguish demonstrated results from aspects that still need assessment. They also provide a clearer basis for evaluating whether the proposed equipment meets the project’s industrial objective.

At MLT Cuccolini, we encourage you to involve our team from the initial assessment and share the available information about your material and process. This gives us the basis to recommend not just a screen, but a configuration suited to the recovery result you need to achieve.

Featured Resources to Keep Learning